Numerical simulation of a polymer melting process using solar energy
DOI:
https://doi.org/10.31349/SuplRevMexFis.1.2.18Keywords:
Phase change, enthalpy formulation, radiation, heat losses.Abstract
In this work, the melting process of a polymeric material is numerically investigated. In general, the heat required for melting plastics is obtained throughout electrical resistances or by burning fossil fuels. The heat transfer mechanisms of these common practices correspond to conduction and convection, respectively. This work explores the feasibility of using radiation as the primary mechanism of energy supply, which has not been widely studied. The energy to achieve the phase change from solid to liquid can be obtained by concentrated solar energy radiation. The total energy required is calculated solving the energy equation using the enthalpy formulation. An explicit formulation with an enthalpy linearization was implemented in the Mathematica programming language and compared with the solution in the commercial softwares Ansys Fluent and COMSOL Multiphysics showing a good agreement. Based upon numerical predictions, it is examined the effects of the relevant parameters, such as incident radiation and convective heat transfer coefficient, on the melting process. It is observed that under weather conditions commonly attained in different cities worldwide, with a radiation of 1000 W/m$^2$ and low convective losses with $h=8$ W/m$^2\cdot$K, the melting process of a cylindrical rod of 3/4 inches diameter can be carried out in around 2 hours.References
L. I. Rubinstein, The Stefan Problem. Translations of Mathematical Monographs : Vol. 27, American Mathematical Society, first edition ed., 1971.
J. Crank, Free and Moving Boundary Problems (Oxford Science Publications). Oxford Science Publications, Oxford University Press, 1984.
S. A. Hu, Henry; Argyropoulos, “Mathematical modelling of solidification and melting: a review,” Modelling and Simulation in Materials Science and Engineering, vol. 4, 07 1996.
V. Alexiades, N. Hannoun, and T. Mai, “Tin melting: effect of grid size and scheme on the numerical solution,” Fifth Mississippi State Conference on Differential Equations and Computational Simulations, pp. 55–69, 2003.
V. Voller and M. Cross, “Accurate solutions of moving boundary problems using the enthalpy method,” International Journal of Heat and Mass Transfer, vol. 24, no. 3, pp. 545–556, 1981.
G. H. Meyer, “Multidimensional stefan problems,” SIAM Journal on Numerical Analysis, vol. 10, no. 3, pp. 522–538, 1973.
M. N. Ozisik, H. R. B. Orlande, M. J. Colaco, and R. M. Cotta, Finite Difference Methods in Heat Transfer. Heat Transfer, CRC Press, second edition ed., 2017.
V. Kumar, F. Durst, and S. Ray, “Modeling moving-boundary problems of solidification and melting adopting an arbitrary lagrangian-eulerian approach,” Numerical Heat Transfer, Part B: Fundamentals, vol. 49, no. 4, pp. 299–331, 2006.
K. R. Sultana, S. R. Dehghani, K. Pope, and Y. S. Muzychka, “Numerical techniques for solving solidification and melting phase change problems,” Numerical Heat Transfer, Part B: Fundamentals, vol. 73, no. 3, pp. 129–145, 2018.
M. D. Muhammad, O. Badr, and H. Yeung, “Validation of a CFD melting and solidification model for phase change in vertical cylinders,” Numerical Heat Transfer; Part A: Applications, vol. 68, no. 5, pp. 501–511, 2015.
B. Gurel, “A numerical investigation of the melting heat transfer characteristics of phase change materials in different plate heat exchanger (latent heat thermal energy storage) systems,” International Journal of Heat and Mass Transfer, vol. 148, p. 119117, 2020.
M. Al-Maghalseh and K. Mahkamov, “Methods of heat transfer intensification in PCM thermal storage systems: Review paper,” Renewable and Sustainable Energy Reviews, vol. 92, no. September 2016, pp. 62–94, 2018.
N. Kousha, M. J. Hosseini, M. R. Aligoodarz, R. Pakrouh, and R. Bahrampoury, “Effect of inclination angle on the performance of a shell and tube heat storage unit - An experimental study” Applied Thermal Engineering, vol. 112, pp. 1497–1509, 2017.
Y. Yuan, X. Cao, B. Xiang, and Y. Du, “Effect of installation angle of fins on melting characteristics of annular unit for latent heat thermal energy storage,” Solar Energy, vol. 136, pp. 365 – 378, 2016.
E. Assis, L. Katsman, G. Ziskind, and R. Letan, “Numerical and experimental study of melting in a spherical shell,” International Journal of Heat and Mass Transfer, vol. 50, no. 9-10, pp. 1790–1804, 2007.
H. M.Weingrill, K. Resch-Fauster, T. Lucyshyn, and C. Zauner, “High-density polyethylene as phase-change material: Longterm stability and aging,” Polymer Testing, vol. 76, no. December 2018, pp. 433–442, 2019.
C. Zauner, F. Hengstberger, M. Etzel, D. Lager, R. Hofmann, and H. Walter, “Experimental characterization and simulation of a fin-tube latent heat storage using high density polyethylene as PCM,” Applied Energy, vol. 179, pp. 237–246, 2016.
IRENA, “Solar heat for industrial processes,” technology brief, EA-ETSAP and IRENA, 2015.
C. D. Han, Rheology and Processing of Polymeric Materials, vol. Volume 2. Oxford University Press, 2007.
W. Minkowycz, Advances In Numerical Heat Transfer, vol. Volume 1. CRC Press, 1996.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2020 José Núñez González, Alberto Beltrán Morales, Michel Rivero Corona, José Daniel Vega Munguía
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors retain copyright and grant the Suplemento de la Revista Mexicana de Física right of first publication with the work simultaneously licensed under a CC BY-NC-ND 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
