Effect of deposition time on properties of the ZnO by USD Method

Authors

  • Noureddine Madaoui Center for the Development of Advanced Technologies (CDTA)
  • Mourad Azibi Center for the Development of Advanced Technologies (CDTA)
  • Ikram Djabrouhou Faculty of Science and Technology, University of Khemis Miliana
  • Nadia Saoula Center for the Development of Advanced Technologies (CDTA)

DOI:

https://doi.org/10.31349/RevMexFis.70.031001

Keywords:

304 L Stainless steel (SS), ZnO thin films, ultrasonic spray deposition (USD) technique, and corrosion behavior.

Abstract

This investigation aims to improve the properties of 304 L stainless steel (SS) substrates for use in corrosion, mechanical, and biomedical applications by depositing ZnO thin films. The ultrasonic spraying technique was used to prepare ZnO thin films with depositional times of 1, 4, and 9 minutes. XRD and Raman studied the surface characteristics of ZnO samples. XRD analysis revealed a hexagonal structure with an average crystallite size of 22 nm for ZnO. Indentation nano measurements indicated an increase in the hardness of the films examined. To determine the type of conductivity and estimate the charge carrier density, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and Mott-Schottky analysis were performed. The thin film deposited for 9 minutes was found to be the most effective in improving corrosion resistance.

References

F. L. Nie, S. G. Wang, Y. Wang, S. C. Wei, Y. F. Zheng, Comparative study on corrosion resistance and in vitro biocompatibility of bulk nanocrystalline and microcrystalline biomedical 304 stainless steel, Dental Materials, 27 (2011) 677, https://doi.org/10.1016/j.dental.2011.03.009

D. Xu et al., Accelerated corrosion of 2205 duplex stainless steel caused by marine aerobic Pseudomonas aeruginosa biofilm, Bioelectrochemistry, 113 (2017) 1, https://doi.org/10.1016/j.bioelechem.2016.08.001

J. Park, J. S. Kim, D. Y. Lee, and S. H. Lee, Real-time monitoring of stress corrosion cracking in 304 L stainless steel pipe using acoustic emission, Journal of Nuclear Materials, 571 (2022) 154009, https://doi.org/10.1016/j.jnucmat.2022.154009

J. R. Aggas, A. Bhat, B. K. Walther, and A. Guiseppi-Elie, Nano-Pt ennobling of stainless steel for biomedical applications, Electrochimica Acta, 301 (2019) 153, https://doi.org/10.1016/j.electacta.2019.01.177

P. Bansal, G. Singh, and H. S. Sidhu, Investigation of surface properties and corrosion behavior of plasma sprayed HA/ZnO coatings prepared on AZ31 Mg alloy, Surface and Coatings Technology, 401 (2020) 126241, https://doi.org/10.1016/j.surfcoat.2020.126241

S. F. Almojil et al., Constructing a ZnO/CuCo2O4 p-n heterojunction photocatalyst for efficiently hexavalent chromiumphenol detoxification and nitrogen fixation, Journal of Physics and Chemistry of Solids, 172 (2023) 111057, https://doi.org/10.1016/j.jpcs.2022.111057

S. Ferraris, and S. Spriano, Antibacterial titanium surfaces for medical implants, Materials Science and Engineering: C, 61 (2016) 965, https://doi.org/10.1016/j.msec.2015.12.062

K. Lesniak-Ziołkowska et al., Electrochemical modification of the Ti15Mo alloy surface in solutions containing ZnO and Zn3(PO4)2 particles, Materials Science and Engineering: C, 115 (2020) 111098, https://doi.org/10.1016/j.msec.2020.111098

G. Calabrese et al., Structural and antibacterial studies of novel ZnO and ZnxMn1-xO nanostructured titanium scaffolds for biomedical applications, Biomaterials Advances, (2022) 213193, https://doi.org/10.1016/j.bioadv.2022.213193

A. Nigam, S. Saini, A. K. Rai, and S. J. Pawar, Structural, morphological, antimicrobial, and cytotoxicity study of spindle-shaped ZnO submicron particles for potential biomedical applications, Materials Today Communications, 28 (2021) 102683, https://doi.org/10.1016/j.mtcomm.2021.102683Getrightsandcontent

N. Al-Hardan, M. Abdullah, and A. Abdul Aziz, Effect of low H2 concentrations on the currentvoltage characteristic of ZnO gas sensor, Advances in Applied Ceramics, 109 (2010) 436, https://doi.org/10.1179/174367510X12722693956275

S. Mun, M. Maniruzzaman, H.-U. Ko, A. Kafy, and J. Kim, Preparation and characterisation of cellulose ZnO hybrid film by blending method and its glucose biosensor application, Materials Technology, 30 (2015) B150, https://doi.org/10.1179/1753555714Y.0000000197

A. Nigam, S. Saini, A.K. Rai, and S.J. Pawar, Structural, optical, cytotoxicity, and antimicrobial properties of MgO, ZnO and MgO/ZnO nanocomposite for biomedical applications, Ceramics International, 47 (2021) 19515, https://doi.org/10.1016/j.ceramint.2021.03.289

F. Ahmad, and A. Maqsood, Complex impedance, dielectric constant, electric modulus, and conductivity analysis of Cd doped ZnO nanostructures at high temperatures, Physica E: Lowdimensional Systems and Nanostructures, 143 (2022) 115353, https://doi.org/10.1016/j.physe.2022.115353

P.-J. Lu, S.-C. Huang, Y.-P. Chen, L.-C. Chiueh, D.Y.-C. Shih, Analysis of titanium dioxide and zinc oxide nanoparticles in cosmetics, Journal of Food and Drug Analysis, 23 (2015) 587, https://doi.org/10.1016/j.jfda.2015.02.009

A. Nigam, S. Pawar, Structural, optical, antimicrobial properties with drug loading and drug release of five different ZnO nano and sub-micron particles for biomedical applications, Materials Technology, 37 (2022) 1716, https://doi.org/10.1080/10667857.2021.1978636

I. Erol, O. Hazman, M. Aksu, E. Bulut, Synergistic effect of ZnO nanoparticles and hesperidin on the antibacterial properties of chitosan, Journal of Biomaterials Science, Polymer Edition, 33 (2022) 1973, https://doi.org/10.1080/09205063.2022.2099668

C.F. Mah, F.K. Yam, Z. Hassan, Investigation and Characterization of ZnO Nanostructures Synthesized by Electrochemical Deposition, Procedia Chemistry, 19 (2016) 83, https://doi.org/10.1016/j.proche.2016.03.119

J. Chen, et al., Multi-technique investigation of Ni-doped ZnO thin films on sapphire by metalorganic chemical vapor deposition, Journal of Vacuum Science & Technology A, 39 (2021). https://doi.org/10.1116/6.0000816

P. Dutheil, J.C. Orlianges, A. Crunteanu, A. Catherinot, C. Champeaux, AlN, ZnO thin films and AlN/ZnO or ZnO/AlN multilayer structures deposited by PLD for surface acoustic wave applications, physica status solidi (a), 212 (2015) 817, https://doi.org/10.1002/pssa.201431747

R. Schifano et al., Schottky contacts to ZnO layers grown by Atomic Layer Deposition: effects of H2O2 functionalization and transport mechanisms, Applied Surface Science, 552 (2021) 149067, https://doi.org/10.1016/j.apsusc.2021.149067

M. Kolhep, C. Sun, J. Blasing, B. Christian, M. Zacharias, Epitaxial growth of highly textured ZnO thin films on Si using an AlN buffer layer by atomic layer deposition, Journal of Vacuum Science et Technology A, 39 (2021) 000793. https://doi.org/10.1116/6.0000793

N. Saoula, L. Bait, S. Sali, M. Azibi, A. Hammouche, and N. Madaoui, Reactive Magnetron Sputter Deposition of Titanium Oxynitride TiNxOy Coatings: Influence of Substrate Bias Voltage on the Structure, Composition, and Properties, Protection of Metals and Physical Chemistry of Surfaces, 55 (2019) 743, https://doi.org/10.1134/S207020511904018X

M. Adar et al., Elaboration and characterization of zno thin films structural and optical study, Physics: Conference Series, 1292 (2019) 012009, https://doi.org/10.1088/1742-6596/1292/1/012009

T. Ramkumar, M. Selvakumar, M. Mohanraj, P. Chandramohan, P. Narayanasamy, Microstructure and corrosion behavior of ZnO-Mg coating on AISI 4140 steel fabricated by spray coating, Journal of Materials Engineering and Performance, 29 (2020) 5796, https://doi.org/10.1007/s11665-020-05099-9

Y. Ma et al., Improved corrosion protective performance of chitosan coatings reinforced with nano-ZnO on degradable magnesium alloy in simulated body fluid, Applied Physics A, 127 (2021) 1, https://doi.org/10.1007/s00339-021-05120-5

M.V. Lungu et al., Functional properties improvement of Ag-ZnO thin films using Inconel 600 interlayer produced by electron beam evaporation technique, Thin Solid Films, 667 (2018) 76, https://doi.org/10.1016/j.tsf. 2018.09.055

Y.D.S. Pambudi et al., Effects of annealing temperature on the electrochemical characteristics of ZnO microrods as anode materials of lithiumion battery using chemical bath deposition, Ionics, 25 (2019) 457, https://doi.org/10.1007/s11581-018-2723-z

S. Demirel, N. Savcak, Corrosion Behavior of 304 L Steel Coated with PVB/PAn-Nano Metal Oxide (TiO2, ZnO), Protection of Metals and Physical Chemistry of Surfaces, 58 (2022) 592, https://doi.org/10.1134/s2070205122030054

M. Roknian, A. Fattah-alhosseini, S.O. Gashti, and M.K. Keshavarz, Study of the effect of ZnO nanoparticles addition to PEO coatings on pure titanium substrate: Microstructural analysis, antibacterial effect and corrosion behavior of coatings in Ringer’s physiological solution, Journal of Alloys and Compounds, 740 (2018) 330, https://doi.org/10.1016/J.JALLCOM.2017.12.366

J. Qu, M. Ascencio, L. Jiang, S. Omanovic, and L. Yang, Improvement in corrosion resistance of WE43 magnesium alloy by the electrophoretic formation of a ZnO surface coating, Journal of Coatings Technology and Research, 16 (2019) 1559, https://doi.org/10.1007/s11998-019-00212-7

R.T. Heintzkill, K.C. Flannagan-Morris, and N. Abu-Zahra, Surface wetting of silver-doped sol-gel ZnO films, Surface Engineering, 36 (2020) 607, https://doi.org/10.1080/02670844.2019.1661144

S. Benramache, Y. Aoun, A. Charef, B. Benhaoua, S. Lakel, Transition width effect on optical characterizations of ZnO thin films deposited by spray ultrasonic, Inorganic and Nano-Metal Chemistry, 49 (2019) 177, https://doi.org/10.1080/24701556.2019.1624568

M. Othmane et al., Modulation of Physical Properties of Sprayed ZnO Thin Films by Substrate Temperature for Optical Applications, International Journal of Nanoscience, 15 (2016) 1650007, https://doi.org/10.1142/S0219581X16500071

C.C.F. Xavier, J.O. Braga, M.O. Pessoa, T. Matencio, and V.F.C. Lins, Corrosion resistance of stainlesssteel surgical tools in enzymatic and alkaline detergent, Materials Today Communications, 33 (2022) 104453, https://doi.org/10.1016/j.mtcomm.2022.104453

J. Wu et al., Micro mechanical property investigations of Nibased high-temperature alloy GH4169 based on nanoindentation and CPFE simulation, International Journal of Solids and Structures, 258 (2022) 111999, https://doi.org/10.1016/j.ijsolstr.2022.111999

A. Kehal, N. Saoula, S.-E.-H. Abaidia, C. Nouveau, Effect of Ar/N2 flow ratio on the microstructure and mechanical properties of Ti-Cr-N coatings deposited by DC magnetron sputtering on AISI D2 tool steels, Surface and Coatings Technology, 421 (2021) 127444, https://doi.org/10.1016/j.surfcoat.2021.127444

A. Burleigh et al., Artificial intelligence based analysis of nanoindentation load-displacement data using a genetic algorithm, Applied Surface Science, 612 (2023) 155734, https://doi.org/10.1016/j.apsusc.2022.155734

C.C. J. Wang, M. Jin, Y. Zhu, and N. Zhang, The carbon dots modified ZnO films photodetector with broadband and fast photoresponse, Optical Materials, 135 (2023) 113341, https://doi.org/10.1016/j.optmat.2022.113341

L. Radjehi, A. Djelloul, S. Lamri, M. F. Slim, and M. Rahim, Oxygen effect on structural and optical properties of zinc oxide, Surface Engineering, 35 (2019) 520, https://doi.org/10.1080/02670844.2018.1515842

G. Williamson, and W. Hall, X-ray line broadening from filed aluminium and wolfram, Acta Metallurgica, 1 (1953) 22, https://doi.org/10.1016/0001-6160(53)90006-6

M. Dhanam, R. R. Prabhu, and P. Manoj, Investigations on chemical bath deposited cadmium selenide thin films, Materials Chemistry and Physics, 107 (2008) 289, https://doi.org/10.1016/j.matchemphys.2007.07.011

N. Madaoui, N. Saoula, L. Zougar, I. Djabrouhou, S. Sali, S. Kermadi, Effect of TiO2 Coating Thickness on the Structure, Mechanical Properties, and Corrosion Behavior of AISI 304L Stainless Steel, Journal of Materials Engineering and Performance, (2022) 1, https://doi.org/10.1007/s11665-022-07144-1

M. Xin, Optical properties of nanostructured ZnO:Eu film by sol-gel method, Surface Engineering, 35 (2019) 947, https://doi.org/10.1080/02670844.2019.1573344

K. Ravichandran, E. Sindhuja, R. Uma, T. Arun, Photocatalytic efficacy of ZnO films - light intensity and thickness effects, Surface Engineering, 33 (2017) 512, https://doi.org/10.1080/02670844.2016.1270797

M. Podia, and A.K. Tripathi, Structural, optical and luminescence properties of ZnO thin films: Role of hot electrons defining the luminescence mechanisms, Journal of Luminescence, 252 (2022) 119331, https://doi.org/10.1016/j.jlumin.2022.119331

Z. Khan, A.S. Alshammari, M. Bouzidi, M. Shkir, and D. Shukla, Improved optoelectronic performance of sol-gel derived ZnO nanostructured thin films, Inorganic Chemistry Communications, 132 (2021) 108812, https://doi.org/10.1016/j.inoche.2021.108812

Y. Rati et al., Visible light assisted degradation of Rhodamin B by reusable S-doped ZnO thin film photocatalyst, Optical Materials, 135 (2023) 113370, https://doi.org/10.1016/j.optmat.2022.113370

A. S. Rini, Y. Rati, A. A. Umar, N. A. Abdullah, Investigation of Structural, Morphological and Optical Properties of Sulfur Doped Zinc Oxide Nanorod, International Journal of Nanoelectronics, Materials, 13 (2020) 21, https://dspace.unimap.edu.my:80/xmlui/handle/123456789/69808

M. Azibi, N. Saoula, N. Madaoui, H. Aknouche, Effects of Nitrogen Content on the Structural, Mechanical, and Corrosion Properties of ZrN Thin Films Grown on AISI 316L by Radiofrequency Magnetron Sputtering, Crystal Research and Technology, 56 (2021) 2100096, https://doi.org/10.1002/crat.202100096

. 51. V. Kumar, N. Singh, R. Mehra, A. Kapoor, L. Purohit, H. Swart, Role of film thickness on the properties of ZnO thin films grown by sol-gel method, Thin Solid Films, 539 (2013) 161, https://doi.org/10.1016/j.tsf.2013.05.088

M. Islam, M. Hossain, S. Razzak, M. Haque, and D. Saha, Effect of deposition time on nanostructure ZnO thin films synthesized by modified thermal evaporation technique, Journal of Nanoscience and Nanotechnology, 16 (2016) 9190, https://doi.org/10.1166/jnn.2016.12901

Z. Khan, A.S. Alshammari, M. Bouzidi, M. Shkir, and D. Shukla, Improved optoelectronic performance of sol-gel derived ZnO nanostructured thin films, Inorganic Chemistry Communications, 132 (2021) 108812, https://doi.org/10.1016/j.inoche.2021.108812

Y. Rati et al., Visible light assisted degradation of Rhodamin B by reusable S-doped ZnO thin film photocatalyst, Optical Materials, 135 (2023) 113370, https://doi.org/10.1016/j.optmat.2022.113370

A. S. Rini, Y. Rati, A. A. Umar, N. A. Abdullah, Investigation of Structural, Morphological and Optical Properties of Sulfur Doped Zinc Oxide Nanorod, International Journal of Nanoelectronics, Materials, 13 (2020) 21, https://dspace.unimap.edu.my:80/xmlui/handle/123456789/69808

M. Azibi, N. Saoula, N. Madaoui, H. Aknouche, Effects of Nitrogen Content on the Structural, Mechanical, and Corrosion Properties of ZrN Thin Films Grown on AISI 316L by Radiofrequency Magnetron Sputtering, Crystal Research and Technology, 56 (2021) 2100096, https://doi.org/10.1002/crat.202100096

V. Kumar, N. Singh, R. Mehra, A. Kapoor, L. Purohit, H. Swart, Role of film thickness on the properties of ZnO thin films grown by sol-gel method, Thin Solid Films, 539 (2013) 161, https://doi.org/10.1016/j.tsf.2013.05.088

M. Islam, M. Hossain, S. Razzak, M. Haque, and D. Saha, Effect of deposition time on nanostructure ZnO thin films synthesized by modified thermal evaporation technique, Journal of Nanoscience and Nanotechnology, 16 (2016) 9190, https://doi.org/10.1166/jnn.2016.12901

N. C. Vega, B. Straube, O. Marin-Ramirez, and D. Comedi, Low temperature chemical vapor deposition as a sustainable method to obtain c-oriented and highly UV luminescent ZnO thin films, Materials Letters, 333 (2023) 133684, https://doi.org/10.1016/j.matlet.2022.133684

G. Demircan et al., Sol-gel synthesis of Si-ZnO, Ti-ZnO and Si-Ti-ZnO thin films: Impact of Si and Ti content on structural and optical properties, Materials Today Communications, 34 (2023) 105234, https://doi.org/10.1016/j.mtcomm.2022.105234

V. Russo, M. Ghidelli, P. Gondoni, C. S. Casari, A. Li Bassi, Multi-wavelength Raman scattering of nanostructured Al-doped zinc oxide, Journal of Applied Physics, 115 (2014) 073508, https://doi.org/10.1063/1.4866322

F. Decremps, J. Pellicer-Porres, A. M. Saitta, J.-C. Chervin, A. Polian, High-pressure Raman spectroscopy study of wurtzite ZnO, Phys. Rev. B, 65 (2002) 092101, https://doi.org/10.1103/PhysRevB.65.092101

O. Marin, T. Soliz, J.A. Gutierrez, M. Tirado, C. Figueroa, D. Comedi, Structural, optical and vibrational properties of ZnO: M (M= Al3+ and Sr2+) nano and micropowders grown by hydrothermal synthesis, Journal of Alloys and Compounds, 789 (2019) 56, https://doi.org/10.1016/j.jallcom.2019.03.115

G. Dovbeshko et al., Raman modes and mapping of graphene nanoparticles on Si and photonic crystal substrates, Optical Materials: X, 15 (2022) 100163, https://doi.org/10.1016/j.omx.2022.100163

Z. Mao, C. Fu, X. Pan, X. Chen, H. He, W. Wang, Y. Zeng, Z. Ye, Raman-based measurement of carrier concentration in ntype ZnO thin films under resonant conditions, Physics Letters A, 384 (2020) 126148, https://doi.org/10.1016/j.physleta.2019.126148

R. Wang, G. Xu, P. Jin, Size dependence of electron-phonon coupling in ZnO nanowires, Physical Review B, 69 (2004) 113303, https://doi.org/10.1103/PhysRevB.69.113303

K. Nur et al., Mechanical properties of cold sintered ZnO investigated by nanoindentation and micro-pillar testing, Journal of the European Ceramic Society, 42 (2022) 512, https://doi.org/10.1016/j.jeurceramsoc.2021.10.011

H. Wang, R. Li, M. Zhou, J. Cedelle, Z. Huang, Q. Wang, Grain boundary sliding mechanism in plastic deformation of nano-grained YAG transparent ceramics: Generalized self-consistent model and nanoindentation experimental validation, Journal of the European Ceramic Society, 37 (2017) 2705, https://doi.org/10.1016/j.jeurceramsoc.2017.02.010

H. M. Wang et al., Unique mechanical properties of nanograined YAG transparent ceramics compared with coarsegrained partners, Materials Design, 105 (2016) 9-15. https://doi.org/10.1016/j.matdes.2016.04.094

L. Liu, Y. Meng, C. Dong, Y. Yan, A.A. Volinsky, and L.-N. Wang, Initial formation of corrosion products on pure zinc in simulated body fluid, Journal of Materials Science Technology, 34 (2018) 22712282, https://doi.org/10.1016/j.jmst.2018.05.005

J.S. Daubert et al., Corrosion protection of copper using Al2O3, TiO2, ZnO, HfO2, and ZrO2 atomic layer deposition, ACS Applied Materials Interfaces, 9 (2017) 4192, https://doi.org/10.1021/acsami.6b13571

M. S. VP, S. Kumar, M. Sivakumar, S. R. Mohan, Enhancement of anticorrosion properties of stainless steel 304L using nanostructured ZnO thin films, AIMS Materials Science, 5 (2018) 932, https://doi.org/10.3934/matersci.2018.5.932

R. Nowosielski, A. Bajorek, R. Babilas, Corrosion behavior of bioresorbable Ca-Mg-Zn bulk metallic glasses, Journal of NonCrystalline Solids, 447 (2016) 126, https://doi.org/10.1016/j.jnoncrysol.2016.05.037

A. M. Oje, A. A. Ogwu, A. I. Oje, N. Tsendzughul, S. Ur Rahman, A comparative study of the corrosion and ion release behaviour of chromium oxide coatings exposed to saline, Ringer’s and Hank’s physiological solutions, Corrosion Science 167 (2020) 108533. https://doi.org/10.1016/j.corsci.2020.108533

M. Sabzi, S. M. Far, S. M. Dezfuli, Characterization of bioactivity behavior and corrosion responses of hydroxyapatite-ZnO nanostructured coating deposited on NiTi shape memory alloy, Ceramics International, 44 (2018) 21395, https://doi.org/10.1016/j.ceramint.2018.08.197

N. Madaoui et al., The effect of substrate bias voltage on the electrochemical corrosion behaviors of thin film deposited on stainless steel by r. f magnetron sputtering, Protection of Metals and Physical Chemistry of Surfaces, 53 (2017) 527, https://doi.org/10.1134/S2070205117030157

N. Madaoui, L. Bait, K. Kheyar, and N. Saoula, Effect of argonoxygen mixing gas during magnetron sputtering on TiO2 coatings, Advances in Materials Science and Engineering, 2017, https://doi.org/10.1155/2017/4926543

G. Ortiz Rabell, M. R. Alfaro Cruz, and I. Juarez-Ramırez, Photochemistry of ZnO/GeO2 film for H2 production, Journal of Photochemistry and Photobiology A: Chemistry, 433 (2022) 114185, https://doi.org/10.1016/j. jphotochem.2022.114185

L. Su, Z. Guan, Q. Liu, Y. Zhu, Ohmic-Schottky conversion of ZnO/metal contact modulated by a plasma surface treatment method, Results in Materials, 15 (2022) 100290, https://doi.org/10.1016/j.rinma.2022.100290

Y. Wang, Z. J. Peng, Q. Wang, X. L. Fu, Tunable electrical resistivity of oxygen-deficient zinc oxide thin films, Surface Engineering, 33 (2017) 217, https://doi.org/10.1080/02670844.2016.1212519

P.J. Navarro-Gazquez et al., Influence of Zn(NO3)2 concentration during the ZnO electrodeposition on TiO2 nanosponges used in photoelectrochemical applications, Ceramics International, 48 (2022) 14460, https://doi.org/10.1016/j.ceramint.2022.01.339

P. Batista-Grau et al., Indirect charge transfer of holes via surface states in ZnO nanowires for photoelectrocatalytic applications, Ceramics International, 48 (2022) 21856, https://doi.org/10.1016/j.ceramint.2022.04.170

H. Amegroud et al., A comprehensive investigation of the electrochemical behavior of nickel-aluminum bronze alloy in alkaline solution: The effect of film formation potential, Colloids and Surfaces A: Physicochemical and Engineering Aspects, 614 (2021) 126126, https://doi.org/10.1016/j.colsurfa.2020.126126

Downloads

Published

2024-05-01

How to Cite

[1]
N. Madaoui, M. . Azibi, I. Djabrouhou, and N. Saoula, “Effect of deposition time on properties of the ZnO by USD Method”, Rev. Mex. Fís., vol. 70, no. 3 May-Jun, pp. 031001 1–, May 2024.

Issue

Vol. 70 No. 3 May-Jun (2024): Revista Mexicana de Física

Section

10 Material Sciences

License

Copyright (c) 2024 Noureddine Madaoui, Mourad Azibi , Ikram Djabrouhou , Nadia Saoula

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors retain copyright and grant the Revista Mexicana de Física right of first publication with the work simultaneously licensed under a CC BY-NC-ND 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.